Additional Information

Site Information

  • Image 1

ESD Drafting Stool, High Back, Full Seat

$1,395.00 $781.00
(You save $614.00)
SKU:
806DRAFTESDN
Quantity:
  • ESD Drafting Chair with all the controls, ESD and wider back and seat

    This ESD Chair is designed for user's who require proven ESD protection and all the comforts of a great ergonomic chair. Complete control of back angle and height so you can customize the back to your back. This will permit your back to rest into the chair and reduce the stress and tension in your back and shoulders. And then you can use the dial-in lumbar control to increase or decrease the amount of low back support.

    The seat depth adjustments will let you make the seat shorter or longer to best support your legs. And if you want to set the chair in an upright or reclined position you can. Height Adjustable Foot ring provides a wider ring for better foot support. And this is all top to bottom ESD certified. Every chair component is grounded to each other all the way down to the ESD casters and floor chain.


    • Extra Wide seat and upright backrest fits tall athletic bodies
    • Dimensions seat 22 w x 18-21d, back 19 w x 22 h, height 21 - 28
    • Dial-in adjustable lumbar support customizes comfort
    • Sliding seat adjusts from 18 to 21 deep
    • Stress relieving ESD Cushion with Medical Grade Foam
    • Backrest forward and backward tilt adjustment
    • True waterfall front with 2 layer medical grade foam
    • Large 5-star, scuff resistant base with ESD casters
    • 7-position adjustable armrests
    • Rated up to 300 Pound Capacity
    • 12-year warranty
    • ESD Drafting Stool with "Complete Circuit" design
  • Specifications Esd Chairs Fabric and Vinyl
    Resistivity:

    TREK Meter; 20% relative humidity, ohms/sq1.3 x 10 exp 6

    X-Static

    Contents 99% Nylon, 1% Carbon Fiber (with Latex Backing)

    Weight

    16.0 ozs. per linear yard Width 54-

    Flammability

    State of CA Technical Bulletin 117, Section E Passes UFAC Class 1

    Color Fastness:

    Light (AATCC-16A) 40 hrs. min., Class 5 Crocking (AATCC-8) Dry Class 5, Wet Class 5

    Stat-Con Vinyl

    Weight 26.0 ozs. per linear yard, Width 54 Resistivity: Beckman Megohmeter, 500 volt charge <1 .0 x 10 exp 6 ohms/sq

    Abrasion Resistance

    (ASTM D-4157) 180,000 Double Rubs Seam Slippage (ASTM D-434) Warp 56 lb. Fill 55 lb. Pilling Resistance (ASTM D-3511) Class 5

    lammability

    State of CA Technical Bulletin 117, Section E Passes, MVSS302 Passes

    General Information

    The problems associated with static electricity have become a major issue for many businesses in this high-tech world. The fabrics shown on this card can help serve as conductors which can carry off static charges before sufficient buildup can occur to create the sparking discharge that can cause computer and instrument malfunction. To maximize the conductive properties of these fabrics and achieve proper performance, engineering of the furniture must take into consideration the need for grounding the static charges conducted by the surface materials.

    This term and any corresponding data refer to typical performance in the tests indicated and should not be construed to imply the behavior of this or any other material under actual fire conditions.

    esd-xs901L.jpg
    esd-xs806L.jpg

    ESD Fabric Black

    ESD Fabric Gray

    esd-xs805L.jpg
    esd-xs500L.jpg

    ESD Fabric Charcoal

    ESD Fabric Green

    esd-xs303L.jpg
    esd-xs-408L.jpg

    ESD Fabric Red

    ESD Fabric Navy Blue

    esd-xs-407L.jpg
    esd-sc-micron-blueL.jpg

    ESD Fabric Blue/Silver

    ESD Vinyl Blue

    esd-sc-blackL.jpg

    ESD Vinyl Black

    Foot Ring Assembly and Adjustment
    Turn_Style_Foot_Ring.jpg
    Prep: Clean Cylinder, Loosen Foot Ring Gasket

    Before Assembly: Clean the cylinder thoroughly to remove any grease or oil to provide a good grip. In the loosened position, check to see that Foot Ring is at the top of the central hub by holding onto the black inner gasket and turning the foot ring counter clockwise. (Tip: The inner gasket needs to be loose so you can fit the foot ring over the chair cylinder.)

    Footring-illust-1.jpg
    footring-illust-2.jpg
    Assembly: Put Foot Ring On Chair Cylinder

    Slide the chair height cylinder into the center opening of the foot ring. Insert the thicker part of the cylinder into the five star base. Insert the thinner part of the cylinder into the chair mechanism attached to the bottom of the chair seat. To engage the pressure seal, sit on the chair and adjust the seat height up and down.

    footring-illust-3.jpg
    Adjust: Height Of Foot Ring

    Hold the plastic inner hub (gasket) of the Foot Ring while you tighten or loosen it. (Tip: If needed, grip the bottom of gasket below foot ring with a cloth and channel locks so you can get a better grip.) Once the Foot Ring is loosened you can move it to the desired height to support the user's legs. Set the height so the user's legs are parallel to the floor or as close as possible. Now you can tighten the Foot Ring. Hold the base with one hand and turn the Foot Ring clockwise to tighten. You may need to hold the bottom of the hub (the black inner gasket) as you turn the Foot Ring in order to get a very tight fit. It is best not to over tighten the Foot Ring

    footring-illust-4.jpg
    footring-illust-5.jpg
  • Write Review

    This product hasn't received any reviews yet. Be the first to review this product!